Kent Hydro Jetting logo
Grey trailer-mounted water jetter with its hose run across a wet driveway into an open PVC sewer cleanout beside a grey rambler house under tall firs

Hydro jetting in Kent, WA

Sewer Camera Inspection in Kent, WA

  • Angi's Seattle range for a standard camera inspection: $220 to $440
  • HomeGuide's national figures: $125 to $500 where a cleanout exists, up to $750 where there isn't one
  • Roughly an hour on site, more if the drain is still blocked or access is through a toilet (HomeGuide)
  • Professional drain cameras reach 200 to 400 feet (HomeGuide)
  • Seattle-area camera runs on a clay line: $440 to $730 (Angi)

Kent Hydro Jetting passes your request to an independent plumber for a camera look at your sewer, whether it's after a clog or before you decide on a repair. We charge nothing for the introduction. The plumber sets the price; ask them to talk you through what the footage shows.

Get a free hydro jetting estimate

Free for homeowners and businesses. One local contractor contacts you.

Sewer Camera Inspection Jobs on Kent Lines

A camera run is a look, not a fix. HomeGuide is clear that the inspection price doesn't include repairs. What it buys is a clear picture of what is in the pipe and where, so the next step is the right one.

Gloved hands feeding a gray push-cable camera into an outdoor cleanout beside a wet lawn

Diagnostic Camera Run After a Clog

When a line keeps clogging, the camera answers why. HomeGuide describes the sequence: a camera goes in to find the clog and check the pipe, jetting follows if the pipe can take it, and a second run confirms the line is clear. Its camera guide names grease and hair as the most common causes, and points to bellies, low spots where the pipe sags, as places debris collects. Cracks, rust, offset joints and, less often, collapsed sections show up too. The sewer line cleaning page covers the cleaning that usually follows.

Handheld gray locator wand held over a damp front lawn with a cedar hedge behind it

Line Locating and Depth Readings

HomeGuide notes that drain cameras carry a built-in transmitter, so a plumber can mark the exact spot of a problem from above ground. RIDGID's NaviTrack Scout, one such locator, calculates and displays depth when held over the transmitter. RIDGID also lists what throws readings off: transmitter power, soil type and moisture, pipe material, nearby conductive lines, and concrete with rebar. Cast iron buried in concrete gives weaker signals and less accurate depths. The manual's own check is to take a reading, turn the locator half a circle, and read again; if the two differ by more than about 10%, the depth is suspect.

Camera Prices by Pipe Material

Pipe material changes the price because older pipe takes more care to inspect. Angi's Seattle camera guide:

  • PVC: $250 to $440
  • Cast iron: $360 to $580
  • Clay: $440 to $730
  • Orangeburg: $580 to $1,160

The same guide prices the camera itself in tiers: a standard camera with no recording at $220 to $440, an HD camera with possible recording or report at $440 to $870, and specialty cameras (360-degree, self-leveling or for unusual pipe) from $870 to $2,180 or more. Clay and Orangeburg lines are more common in older homes, and the sewer scope page covers what that means for Kent's housing.

Laptop on a workbench in a garage showing paused sewer camera footage of a pipe joint, rain on the window

Recorded Footage for Repair Bids

If the camera finds damage, the recording becomes the document every repair bid is based on. Angi's standard tier doesn't include recording, so say up front that you want the video. Among HomeGuide's suggested questions before booking: is a video copy included, and will there be a printed report of the results? It also warns about companies that charge little for inspections and a lot for repairs. With footage in hand, a second plumber can price the same defect without paying for another run. Any repair to a Kent side sewer needs a permit; see the sewer line repair page.

Gloved hands feeding a jetter hose with a stainless multi-jet nozzle into an open white PVC sewer cleanout in a garden bed

Why Kent homeowners and businesses call Kent Hydro Jetting

  • The request is free, and you decide whether to book
  • One licensed local plumber gets your request, not a call list
  • Ask for a camera look before any pressure goes in
  • Ask for the price in writing before the work starts
  • You pay nothing for the referral

Get a free hydro jetting estimate

Free for homeowners and businesses. One local contractor contacts you.

What a Camera Inspection Costs and How Long It Takes

No guide publishes a Kent price. Angi's Seattle pages are the nearest; national figures fill in the rest. They're market guides, not the plumber's rates.

Camera job Guide range Guide
Standard camera, Seattle $220 to $440 Angi
Line under 50 feet, Seattle $250 to $360 Angi
Standard 50 to 100 foot home line, Seattle $360 to $580 Angi
Line over 100 feet, Seattle $580 to $1,160 Angi
With a cleanout, national $125 to $500 (average $280) HomeGuide
Without a cleanout, national $175 to $750 HomeGuide
Camera added to a jetting job $100 to $300 HomeGuide

HomeGuide puts most inspections at about an hour, longer where there's no cleanout or the drain is clogged. Without a cleanout the camera often goes in through a pulled toilet, which costs more and takes longer. The guides spread widely: Angi and HomeAdvisor's national range runs $275 to $1,800. Price differences mostly come down to length, access, material and whether the run is recorded.

Who pays for a defect the camera finds depends on where it sits. In Kent the owner's side sewer runs all the way to the tee at the public main, as the sewer line cleaning page explains.

Frequently asked questions

The line backed up last night. Can the camera go in before it's cleared?

Often only partway. HomeGuide notes that a major blockage stops the camera from moving forward until it's cleared, and inspections with an active clog take longer. The usual order is a short look to find the blockage, the cleaning, then a full run to check the pipe.

One quote was $250 and another was almost $600. Are both reasonable?

They can be. Angi's Seattle figures move with line length and material: $250 to $360 for runs under 50 feet, $360 to $580 for a standard 50 to 100 foot home line, and up to $1,160 for longer lines or Orangeburg pipe. A camera that records adds cost too. Ask each plumber what length and material they priced.

We're getting repair bids. What should the plumber hand over after the camera run?

A copy of the video and a written report, if they offer one. HomeGuide lists both among the questions to ask before booking. With the footage in hand, every repair bidder is pricing the same crack or belly, and you can check that the dig spot matches what the locator marked.

The camera found a sag halfway to the street. Will jetting fix it?

No. HomeGuide says jetting can't fix structural problems, and a belly is a section where the pipe has sagged and debris collects. Cleaning can buy time, but a belly that keeps refilling is a repair question, and repairs to a Kent side sewer need a permit.

How deep is my side sewer, and can the camera tell me before anyone digs?

A transmitter in the camera head lets a locator above ground find the spot and estimate depth. RIDGID's own manual says depth readings are estimates and that exposing the line is the only way to confirm its location and depth, so treat the mark as a starting point for the dig.

Ready to get started in Kent?

Request a free estimate